5. How to Guides

• 5.1. Host
  • 5.1.1. Moving Files to the Target System
  • 5.1.2. Customizing the SDK Splash Screen
  • 5.1.3. AM335x to AM437x Hardware Migration Guide
    • 5.1.3.1. Introduction
    • 5.1.3.2. Basic Feature Comparison
    • 5.1.3.3. Module Comparison
      • 5.1.3.3.1. Processors
        • 5.1.3.3.1.1. ARM Core
        • 5.1.3.3.1.2. Neon Co-processor
        • 5.1.3.3.1.3. Graphics Engine
        • 5.1.3.3.1.4. System DMA
        • 5.1.3.3.1.5. On-Chip Memory
      • 5.1.3.3.2. Memory Subsystem
        • 5.1.3.3.2.1. General Purpose Memory Controller
        • 5.1.3.3.2.2. External Memory Interface
        • 5.1.3.3.2.3. EMIF Tool
      • 5.1.3.3.3. Power, Reset, and Clock Management
        • 5.1.3.3.3.1. Operating Performance Points
        • 5.1.3.3.3.2. Voltage Rails
        • 5.1.3.3.3.3. Input Clocks
        • 5.1.3.3.3.4. PLLs
        • 5.1.3.3.3.5. Power Management Feature Comparison
        • 5.1.3.3.3.6. Bootmodes
      • 5.1.3.3.4. Multimedia Hardware Components
        • 5.1.3.3.4.1. LCDC vs DSS
        • 5.1.3.3.4.2. DSS FIFO Underflow
      • 5.1.3.3.5. Communication Interfaces
        • 5.1.3.3.5.1. MMC/SD
        • 5.1.3.3.5.2. USB
        • 5.1.3.3.5.3. I2C
        • 5.1.3.3.5.4. UART
        • 5.1.3.3.5.5. Real-Time Clock (RTC)
        • 5.1.3.3.5.6. Ethernet
        • 5.1.3.3.5.7. McSPI
        • 5.1.3.3.5.8. PWM Subsystem (PWMSS)
        • 5.1.3.3.5.9. PRU-ICSS - Programmable Real-time Unit Subsystem and Industrial Communications Subsystem
      • 5.1.3.3.6. Timers
        • 5.1.3.3.6.1. GPTimer
        • 5.1.3.3.6.2. WDTimer
      • 5.1.3.3.7. Misc
        • 5.1.3.3.7.1. GPIOs
      • 5.1.3.3.8. ARM Interrupt Controller
      • 5.1.3.3.9. New interfaces in AM437x
      • 5.1.3.3.10. Pin and package
    • 5.1.3.4. Software Migration Guide
• 5.2. Target
  • 5.2.1. How to Recalibrate the Touchscreen
  • 5.2.2. SDK File System Optimization/Customization
    • 5.2.2.1. The Basics of OPKG
      • 5.2.2.1.1. List all available options of opkg
      • 5.2.2.1.2. Show all installed packages
      • 5.2.2.1.3. Show package contents
      • 5.2.2.1.4. Find a file owner
      • 5.2.2.1.5. Show packages which require the package as dependency
      • 5.2.2.1.6. Removing Packages or Deinstallation
      • 5.2.2.1.7. Install local packages
  • 5.2.3. How to add a JVM
  • 5.2.4. How to use a Mouse instead of the Touchscreen with Matrix
  • 5.2.5. Update U-Boot Environment Variables stored in SPI Flash from Linux
  • 5.2.6. How to change dtb files
  • 5.2.7. How to Fix Y2K38 Issue
    • 5.2.7.1. What is the Y2K38 Issue?
    • 5.2.7.2. Building a Y2K38-friendly Image
• 5.3. Hardware EVM Setup
  • 5.3.1. EVMK2H Hardware Setup Guide
    • 5.3.1.1. Hardware Setup
      • 5.3.1.1.1. FTDI Driver Installation on PC Host
      • 5.3.1.1.2. BMC Version Check and Update
      • 5.3.1.1.3. UCD Power Management Modules In-Field Update
      • 5.3.1.1.4. Attach the Ethernet cable
      • 5.3.1.1.5. Connect the JTAG interface
      • 5.3.1.1.6. K2H Set the boot mode switch SW1
      • 5.3.1.1.7. DDR Configuration (Rev 0B EVM only)
      • 5.3.1.1.8. Attach the serial port cable to the SoC UART port
      • 5.3.1.1.9. Connect the power cable
    • 5.3.1.2. BMC In-Field Update
    • 5.3.1.3. DIP Switch and Bootmode Configurations
      • 5.3.1.3.1. Rev 1.0 EVM SW1 switch Bootmode Configuration
      • 5.3.1.3.2. Changing the Bootmode
    • 5.3.1.4. Connect to EVMK2H using CCS
• 5.4. Board Port
  • 5.4.1. U-Boot Board Port
    • 5.4.1.1. Overview
    • 5.4.1.2. Integrating support for a new board into the U-Boot tree
      • 5.4.1.2.1. Creating an initial baseline by cloning and flattening TI EVM support
      • 5.4.1.2.2. Customizing the newly-established baseline to support actual target platform
      • 5.4.1.2.3. Building out full support for target platform
    • 5.4.1.3. U-Boot Bringup Debugging Tips